-
摘要：本设计为年产量180万吨的中厚板车间工艺设计。设计中介绍了中厚板的历史发展历程，近段时间内的市场需求及今后的主要发展形式。基于目前的情形，确定并制定了生产大纲，编制了合理的金属平衡表。此次设计是以Q345（40mm×4050mm×实长）钢板为典型产品。根据研究资料选择并确认了该产品的生产工艺流程，根据要求选择合理的轧机布置形式，本设计采用双机架纵列式布置。选择了适合生产的辅助设备，并制定出了典型产品的压下制度，计算了轧件力能参数，如：轧制力，变形抗力，传动力矩的计算。校核了轧辊得强度以及电机的容量。确定了车间的劳动组织，工作时间。计算出车间的轧机年产量。然后基于轧机形式和具体参数，综合考虑其他设备的形式，确定设备间距，最终画出本车间的平面布置图。分析了车间的各项经济指标。对于环境保护提出有效意见。37503
- 上一篇：反应型阻燃剂对聚氨酯硬泡阻燃性能影响
- 下一篇：油菜秸秆基聚醚多元醇的合成与表征
毕业论文关键词：中厚板车间；产品大纲；金属平衡表；轧制力；传动力矩
The Annual Production of 180 Million Tons of Plate Plant
Abstract：This design is the annual production of 180 million tons of plate plant. Through the research of plate market to introduce the development of the plate, analyze the plate market demand, and direct the current state of technology to develop a reasonable outline of the products and metal balance sheet. Typical product Q345 (40mm × 4050mm ×actual length )steel-based, to determine the typical products of the process, to determine the mill arrangement of workshop equipment selection, and to develop typical products and reasonable reduction procedures to calculate the rolling force parameters, such as: rolling force calculation, the calculation of the deformation resistance and transmission torque calculation. The check rolls intensity and calculate the capacity of the motor. To determine workshop work systems and working hours, calculated the annual production of the mill, according to the typical product of the process and the size of the rolling determine workshop layout, such as device spacing, warehouse area, and draw a plan of the workshop floor . The analysis of the economic indicators of the workshop. And to take effective environmental protection measures.
Keywords: plate workshop; outline; metal balance sheets; rolling force; deformation resistance; drive torque
目录
1 绪论 1
1.1 国内外中厚板的发展状况 1
1.1.1 中厚板简介 1
1.1.2 国外中厚板轧机发展概况 1
1.1.3 我国中厚板生产所采用的先进技术 3
1.1.4 我国中厚板轧机的改造 5
1.2 本课题的目的和意义 5
2 产品大纲及相关技术要求 6
2.1 产品生产大纲 6
2.2 编制金属平衡表 6
2.2.1 成材率的概念 6
2.2.2 金属平衡分析 7
2.2.3 Q345钢板的化学成分 8
2.2.4 Q345钢板尺寸偏差 8
3 轧机的布置及工艺流程的制定 10
3.1 中厚板生产工艺流程 10
3.2 典型产品的工艺流程 10
3.3 轧制区设备选择 12
3.3.1 中厚板轧机型式 12
3.3.2 中厚板轧机的布置 13
3.3.3 轧机主机列 13
3.3.4 换辊装置 13
3.3.5 轧制区其它设备 14
3.4 辅助设备的选择 14
3.4.1 加热炉 14
3.4.2 高压水除磷装置 14
3.4.3 热矫直机 14
3.4.4 冷床 14