菜单
  

    (3) The mold product level greatly is lower than the international standard
    The production cycle actually is higher than the international water broad product level low mainly to display in the mold precision, cavity aspect and so on surface roughness, life and structure .
    (4) Develops the ability badly, economic efficiency unsatisfactory our country mold enterprise technical personnel proportion low
    The level is lower, also does not take the product development, frequently is in the passive position in the market. Our country each mold staff average year creation output value approximately ,ten thousand US dollars, overseas mold industry developed country mostly 15 to10,000 US dollars, some reach as high as 25 to10,000 US dollars, relative is our country quite part of molds enterprises also continues to use the workshop type management with it, truly realizes the enterprise which the modernized enterprise manages few
    To create the above disparity the reason to be very many, the mold long-term has not obtained the value besides the history in as the product which should have, as well as the most state-owned enterprises mechanism cannot adapt the market economy, but also has the following several reasons: .
    (1) Country to mold industry policy support dynamics also insufficiently
    Although the country already was clear about has promulgated the mold profession industrial policy, but necessary policy few, carried out dynamics to be weak. At present enjoyed the mold product increment duty enterprise nation 185, the majority enterprise still the tax burden is only overweight. The mold enterprise carries on the technological transformations introduction equipment to have to pay the considerable amount the tax money, affects the technology advancement, moreover privately operated enterprise loan extremely difficult .
    (2) Talented person serious insufficient, the scientific research development and the technical attack investment too urine
    Mold profession is the technology, the fund, the work crowded industry, along with the time progress and the technical development, grasps the talented person which and skilled utilizes the new technology exceptionally short, the high-quality mold fitter and the enterprise management talent extremely is also anxious. Because the mold enterprise benefit unsatisfactory and takes insufficiently the scientific research development and the technical attack, the scientific research unit and the universities, colleges and institutes eye stares at is creating income, causes the mold profession invests too few in the scientific research development and the technical attack aspect, causes the mold technological development step not to be big, progresses not quick .
    (3) The craft equipment level to be low, also necessary is not good, the use factor low
    recent years our country engine bed profession progressed quickly, has been able to provide the quite complete precision work equipment, but compared with the overseas equipment, still had a bigger disparity. Although the domestic many enterprises have introduced many overseas advanced equipment, but the overall equipment level low are very more than the overseas many enterprises. As a result of aspect the and so on system and fund reason, introduces the equipment not not necessary, the equipment and the appendix not necessary phenomenon are extremely common, the equipment utilization rate low question cannot obtain the comparatively properly solution for a long time .
    (4) Specialization, standardization, commercialized degree low, the cooperation ability
    Because receives "large and complete" "small and entire" the influence since long ago, mold specialization level low, the specialized labor pision is not careful, the commercialized degree is low. At present domestic every year produces mold, commodity mold minister 40% About, other for from produce uses for oneself. Between the mold enterprise cooperates impeded, completes the comparatively large-scale mold complete task with difficulty. Mold standardization level low, mold standard letter use cave rare is low also to the mold quality, the cost has a more tremendous influence, specially has very tremendous influence .
  1. 上一篇:塑料注射模热流道设计英文文献和中文翻译
  2. 下一篇:提高级进模性能英文文献和中文翻译
  1. 绿色建筑与室内空气质量英文献和中文翻译

  2. 注塑模具设计英文文献和中文翻译

  3. CAD知识的模具设计英文文献和中文翻译

  4. 内河运输船舶碰撞与搁浅...

  5. 产业集群与城市化英文文献和中文翻译

  6. 塑料制品的注塑模具设计...

  7. 轴承的摩擦与润滑英文文献和中文翻译

  8. 杂拟谷盗体内共生菌沃尔...

  9. 电站锅炉暖风器设计任务书

  10. 十二层带中心支撑钢结构...

  11. 乳业同业并购式全产业链...

  12. 大众媒体对公共政策制定的影响

  13. 酸性水汽提装置总汽提塔设计+CAD图纸

  14. 当代大学生慈善意识研究+文献综述

  15. 中考体育项目与体育教学合理结合的研究

  16. 河岸冲刷和泥沙淤积的监测国内外研究现状

  17. java+mysql车辆管理系统的设计+源代码

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回