菜单
  

    •    Prevents oxidation/corrosion of the bearing rolling elements.
    •    Acts as a barrier to contaminants.
    •    Serves as a heat transfer agent.

    Bearing lubricants fall into three main categories: oils, greases and solid dry film lubricants, which are usually limited to moderate speed and very light loading conditions. The selection of a particular type of bearing lubricant is generally governed by the operating conditions and limitations of a bearing system. Factors include:

    •    The viscosity of the lubricant at operating temperature.
    •    The maximum and minimum allowable operating temperatures.
    •    The speed at which the bearing will operate.
    Grease considerations
    The primary advantage of grease over oil is that bearings can be pre-lubricated, eliminating the need for - and the cost of - an external lubrication system. Besides simplicity, grease lubrication also requires less maintenance and has less stringent sealing requirements than oil systems. Grease tends to remain in proximity to bearing components.

    The drawbacks of using grease are that it does not conduct heat away from a bearing as efficiently as oil. Also, grease can increase the initial torque within a bearing and cause running torque to be slightly higher. The speed limits for greases (expressed as an ndm value, with ndm being the rpm multiplied by the bearing PCD in mm) are generally lower than for oils due to the plastic nature of grease that tends to cause overheating at high speeds.

    In certain applications the design of the bearing and the selection of a suitable grease become very challenging. Here, it is critical that the bearing supplier has the knowledge and experience to suggest a grease that ensures maximum reliability of the bearings over long operating periods without re-lubrication. Current "greased-for-life" bearing technology can consistently give 30,000+ hours of life at 700,000 ndm.
     
    Oil considerations
    While grease lubrication is inherently simpler than lubrication with oil, there are still applications where oil is the better choice. In high-speed spindle and turbine applications, for example, oil is supplied continuously and provides cooling as well as lubrication. A further example is instrument bearings with extremely low values of starting and running torque. These require only a minimal, one-time lubrication, each bearing receiving just a few milligrammes of oil.

    The limiting speeds for oil-lubricated bearings are governed by the size of the bearing and the design of the cage, rather than by the lubricant itself. To illustrate this, petroleum or diester-based oils can accommodate bearing speeds of up to 1,500,000 ndm or higher. In the case of silicone-based oils, the maximum speed rating drops to 350,000 ndm. Similarly, when calculating life for bearings lubricated with silicone-based oils, the Basic Load Rating (C) should be reduced by two-thirds (C/3). To ensure long life at high speeds, the lubrication system should provide for retention, circulation, filtration and possibly cooling of the oil.

    In extremely harsh operating environments such as dry pump bearings, often oil selection is pre-defined to a certain extent by the end user. In dry pumps, the challenge for the bearing supplier is to optimise the design of the bearings in order to make the best use of relatively poor lubrication.

    Solid soft film lubricants
    Solid soft films are primarily used to provide solid lubrication for bearings in extreme applications where traditional fluid lubricants would be rendered ineffective. They offer the advantages that their friction is independent of temperature, and they do not evaporate or creep in terrestrial vacuum or space environments.

    The solid soft film lubricant can either be applied directly to the surface or transferred by rubbing contact from a sacrificial source such as a self-lubricating bearing cage.
  1. 上一篇:不规则塑料注塑模具英文文献和中文翻译
  2. 下一篇:红外鼓膜温度计英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 数控机床英文文献和中文翻译

  4. 工业机械手英文文献和中文翻译

  5. 低频振动的铁路车轴的状...

  6. 接头的形状对沥青塞接头...

  7. 数控加工技术英文文献和中文翻译

  8. 大众媒体对公共政策制定的影响

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 电站锅炉暖风器设计任务书

  11. 酸性水汽提装置总汽提塔设计+CAD图纸

  12. 十二层带中心支撑钢结构...

  13. 杂拟谷盗体内共生菌沃尔...

  14. java+mysql车辆管理系统的设计+源代码

  15. 中考体育项目与体育教学合理结合的研究

  16. 当代大学生慈善意识研究+文献综述

  17. 乳业同业并购式全产业链...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回