菜单
  

    a b s t r a c t   This paper presents a new approach based on the application of a multiaxial high cycle fatigue criterion together with the use of El-Haddad correction for investigation of fretting fatigue in railway axles. Stress path along the axle–wheel contact, determined by the FE analysis, was implemented into different mul- tiaxial fatigue criteria in order to predict critical sites of nucleation. The equivalent fatigue limit expressed by the applied criterion is compared with the crack size dependent fatigue limit described by El-Haddad correction in order to define a defect size acceptability criterion. Verification of the pro- posed approach was done by post-test failure investigation of the full-scale axle tests conducted as a part of Euraxles project. Scanning electron microscope (SEM) examination of the failed press-fit sections revealed a critical defect size in the order of 200 lm in depth for non-propagating cracks. The obtained results were found to be consistent with the estimations made by the proposed  approach.69574

    1. Introduction

    Investigation of fretting damage and its prolonged conse- quences in fatigue life assessment is an important issue in railway axle design. Fretting fatigue in the axle–wheel contact can be described as the repetitive micro  sliding  of  the  wheel assembly on press-fit seat due to applied bending and vibration. Multiple- site surface damage caused by fretting is considered to be the source of crack nucleation which can become a propagating crack with further application of cyclic loading. A decreased fatigue life up to 60–75% due to fretting damage has been reported in the lit- erature [1,2].

    The present study is a part of research activity devoted to vali- date the fatigue limits described by the European Standards. Main objective of the present study is to develop an acceptability criteria that can be applied in assessment of surface defects inspected at axle press-fits by magnetic particle inspections (MPI). Further con- tribution to the European Standard EN-13260, which necessitates verification of no crack formation after 107 cycles at fatigue limit currently, by evaluating the applicability of presents fatigue limits in the presence of non-propagating surface cracks was also aimed [3]. In the study, press fit surfaces of different EA4T axles have been investigated.  A  nominal  bending  stress,  not  exceeding  240 MPa,

    was selected in accordance with the EN standards [4–6]. The allow- able stress limit at the press fit was reduced to 132 MPa for an axle with a diameter ratio of D/d = 1.12 (Fig. 1a) [4,5]. Formation and developments of non-propagating cracks at  the  press-fit  under the influence of fretting was  investigated.

    A previous study on fretting fatigue of railway axles identified four typical regions for initiation sites located at the root of transi- tion fillet (T-transition), contact edge, stick–slip interface of the contact and sub-surface under contact [4,5]. Hirakawa et al. reported formation of an annular band of fretting corrosion with a width of 7–9 mm starting from the edge of press-fit to the inner press fitted surface for railway axles. Within this band several min- ute cracks can be observed. However, the cracks which propagated to final failure always observed to initiate from the sites 2–5 mm away from the edge of the press-fit   [7].

    Mechanism of fretting fatigue in railway axle is  explained  by the multiple-site nucleation of non-propagating cracks under the influence of fretting damage described as multiple-site damage (MSD) [8]. Beyond certain limits of loading, framed by application of multiaxial fatigue criteria along the stress path, transformation of non-propagating cracks to a state of propagation might take place. Propagation of long-cracks, driven by the applied bulk stress, results in final fracture of the axle as cyclic loading proceeds [8]. Experimental fretting studies on different materials has shown that majority of fatigue life has been spent in formation of a engi- neering crack in the cases of cylindrical contacts [1,8–13]. In  other

  1. 上一篇:接头的形状对沥青塞接头的影响英文文献和中文翻译
  2. 下一篇:工业机械手英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 接头的形状对沥青塞接头...

  4. 电-气动驱动的垂直计算机...

  5. 开口端纺纱系统中的锥形...

  6. 木质填料聚丙烯复合材料...

  7. 变频器在供水控制系统的...

  8. 当代大学生慈善意识研究+文献综述

  9. 杂拟谷盗体内共生菌沃尔...

  10. 十二层带中心支撑钢结构...

  11. 酸性水汽提装置总汽提塔设计+CAD图纸

  12. 电站锅炉暖风器设计任务书

  13. 乳业同业并购式全产业链...

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. java+mysql车辆管理系统的设计+源代码

  16. 中考体育项目与体育教学合理结合的研究

  17. 大众媒体对公共政策制定的影响

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回