菜单
  
    Five-axis CNC machining centers have become quite common today. The kinematics of most of the machines are based on a
    rectangular Cartesian coordinate system. This paper classifies the possible conceptual designs and actual existing implementations
    based on the theoretically possible combinations of the degrees of freedom. Some useful quantitative parameters, such as the
    workspace utilization factor, machine tool space efficiency, orientation space index and orientation angle index are defined. The
    advantages and disadvantages of each concept are analyzed. Criteria for selection and design of a machine configuration are given.
    New concepts based on the Stewart platform have been introduced recently in industry and are also briefly discussed.  2002
    Elsevier Science Ltd. All rights reserved.7385
    Keywords: Five-axis; Machine tool; Kinematic chain; Workspace; CNC; Rotary axis1. Introduction
    The main design specifications of a machine tool can
    be deduced from the following principles:
     The kinematics should provide sufficient flexibility in
    orientation and position of tool and part.
     Orientation and positioning with the highest poss-
    ible speed.
     Orientation and positioning with the highest poss-
    ible accuracy.
     Fast change of tool and workpiece.
     Save for the environment.
     Highest possible material removal rate.
    The number of axes of a machine tool normally refers
    to the number of degrees of freedom or the number of
    independent controllable motions on the machine slides.
    The ISO axes nomenclature recommends the use of a
    right-handed coordinate system, with the tool axis corre-
    sponding to the Z-axis. A three-axis milling machine has
    three linear slides X, Y and Z which can be positioned
    everywhere within the travel limit of each slide. The tool
    axis direction stays fixed during machining. This limitsthe flexibility of the tool orientation relative to the work-
    piece and results in a number of different set ups. To
    increase the flexibility in possible tool workpiece orien-
    tations, without need of re-setup, more degrees of free-
    dom must be added. For a conventional three linear axes
    machine this can be achieved by providing rotational
    slides. Fig. 1 gives an example of a five-axis milling
    machine.2. Kinematic chain diagram
    To analyze the machine it is very useful to make a
    kinematic diagram of the machine. From this kinematic
    (chain) diagram two groups of axes can immediately be
    distinguished: the workpiece carrying axes and the tool
    carrying axes. Fig. 2 gives the kinematic diagram of the
    five-axis machine in Fig. 1. As can be seen the work-
    piece is carried by four axes and the tool only by one
    axis.
    The five-axis machine is similar to two cooperating
    robots, one robot carrying the workpiece and one robot
    carrying the tool.
    Five degrees of freedom are the minimum required to
    obtain maximum flexibility in tool workpiece orien-
    tation, this means that the tool and workpiece can be
    oriented relative to each other under any angle. The
    minimum required number of axes can also be under-
    stood from a rigid body kinematics point of view. To
    orient two rigid bodies in space relative to each other 6
    degrees of freedom are needed for each body (tool and
    workpiece) or 12 degrees. However any common trans-
    lation and rotation which does not change the relative
    orientation is permitted reducing the number of degrees
    by 6. The distance between the bodies is prescribed by
    the toolpath and allows elimination of an additional
    degree of freedom, resulting in a minimum requirement
    of 5 degrees.
    3. Literature review
    One of the earliest (1970) and still very useful intro-
    ductions to five-axis milling was given by Baughman [1]
  1. 上一篇:注塑模的收缩位移点英文文献和翻译
  2. 下一篇:预制空心板连续双梁桥英文文献和中文翻译
  1. 数控机床英文文献和中文翻译

  2. 数控机床改造英文文献和中文翻译

  3. 机床结构动态性能预测英文文献及中文翻译

  4. 高速切削加工组合机床英文文献和中文翻译

  5. 机床铣削稳定性英文文献和中文翻译

  6. 机床设计英文文献和中文翻译

  7. 精密机床机械英文文献和中文翻译

  8. 十二层带中心支撑钢结构...

  9. 酸性水汽提装置总汽提塔设计+CAD图纸

  10. 中考体育项目与体育教学合理结合的研究

  11. 乳业同业并购式全产业链...

  12. 大众媒体对公共政策制定的影响

  13. 杂拟谷盗体内共生菌沃尔...

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. 当代大学生慈善意识研究+文献综述

  16. java+mysql车辆管理系统的设计+源代码

  17. 电站锅炉暖风器设计任务书

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回