- 上一篇：模具设计中的功能建模英文文献和中文翻译
- 下一篇：注塑模具参数化控制英文文献和中文翻译
In this algorithm, the nearest vertex from the origin in the profile scan lines offset is taken as the start point. The end point is 2d of dis-
tance away from the start point by clockwise; the scanning direction
Eq. (5) enables the coordinate of the endpoint Q2(x2, y2) to be calculated.
Fig. 9. Flow chart of the modified scan line algorithm for nozzle path planning.
Fig. 10. Judgment of the inner and outer profiles.
Fig. 11. Intersection calculation of adjacent segments of a polygon after offset.
Fig. 12. The start point and the endpoint of scanning of the profile.
J. Xu et al. / Automation in Construction 76 (2017) 85–96 91
4.2.2. Scanning of the fill
Scanning of the fill refers to filling the rest region of the profile scan. The algorithm is required for scanning the X-axis and Y-axis orientation for the odd and the even layers. An example of scanning the odd layers is provided.
Assuming the maximum coordinate value of the offset profile path
Table 1
Materials prepared for the experiment. Element Description
Sand Natural river sand with 2.1 fineness modulus and 0.12% moisture
content
Cement P.C32.5R Composite Portland cement
in Y direction isymax, and ymin for the minimum coordinate value, the scanning orientation of the odd scan lines is X-axis positive direction
Water
reducer
Polycarboxylate Superplasticizer
Fiber 3 mm micro polypropylene fibers
and X-axis negative direction for the even ones. This is, however, depen-
dent on their Y coordinate values. When the scanning distance is D, the number of filling scan lines is n =( ymax −ymin)/D −1, then the equation for the No.i filling scan line is:
Y ¼ ymin þ iD; i ¼ 1; 2; 3; …; n: ð6Þ
The scan finishes when the Y coordinate value of a filling scan line meets Y N ymax −D.
When a filling scan line, y = h, intersects with a segment of a offset profile scan line, the equation of the line, where the segment is located, is capably calculated, or rather given, which is here assumed to be Ax+By +C =0 and is expressed as:
. Ax þ By þ C ¼ 0
shapes or even heteromorphosis and no drawings exist; an examples is presented in Fig. 13.
Within the campus at the Huazhong University of Science and Tech- nology (HUST), there are also damaged stone historical plinths similar to those in Fig. 13 and one of them with simple curved surface has been selected for this research to demonstrate the feasibility of the pro- posed digital reproduction process. Notably, the damaged plinth func- tions as an ornamental component for a timber column structure. The role of the plinth is to protect the timber column from water damage and collision, as well provide lateral support and decorative aesthetics.
According to previous Jump table test, a fine aggregate fiber cement
y ¼ h
ð7Þ
mortar is made up for reproduction of the plinth, which has a 0.3 water– cement ratio and a 1:1 sand: cement ratio, plus 0.1% micro polypropyl-
The intersections of the filling scan line and the segment can be cal- culated using Eq. (7). Assuming the horizontal coordinate of the inter- section is x0, the horizontal coordinate of the odd number of endpoint
corresponding to the intersection is x0 +D, or x0 − D for the even num-
-
注塑模具参数化控制英文文献和中文翻译
-
模具设计中的功能建模英文文献和中文翻译
-
高填充聚苯硫醚变温模具...
-
麦克纳姆轮的机器人移动...
-
固液搅拌罐的CFD模拟英文文献和中文翻译
-
塑料注射成型收缩值英文文献和中文翻译
-
模拟列车断裂性能的工具英文文献和中文翻译
超精密工程与纳米技术英文文献和中文翻译
影响大学生网络购物的因素调查问卷
营养条件调控马疫链球菌...
OFDM系统的实时业务资源分配算法研究
机枪架座国内外研究现状和发展趋势
BiFeO3的国内外研究现状
国内外FMECA分析的发展研究现状
STM32智能天然气监控终端的...
H90与D6AC钢感应熔敷焊工艺试验研究
外贸出口竞争力国内外研究现状