菜单
  

    (3)   where δmax = elongation at maximum load (miniature specimen)            εmax = strain at maximum load (standard uniaxial test)  leq  = equivalent gage length of miniature specimen true strain (εt)max = ln(1+εmax)     (4)   hence the value of true strain at the  maximum load can be determined from experimental load-elongation curve. This is the extra advantage of using dumb-bell shaped miniature specimen. This is because miniature specimen is also in  tension mode in the same  fashion as the` standard specimen. This type of relationship is difficult to formulate for miniature shear punch tests.  c)  The miniature load-elongation curve is pided into n linear segments. For each point of load-elongation curve, corresponding strain is determined  by piding the elongation by equivalent gage length. From these strain values, true strains are determined. Elastic strains are subtracted from true strain values in order to get true plastic strains.  d)  The second  data point in the uniaxial true  stress – true plastic  strain curve (σt2,  εt2) can  be obtained by performing the finite element analysis by giving the inputs as load P2, elastic modulus E, the yield stress σt1 and corresponding true plastic strain εt1 which is zero, the true plastic strain εt2 and corresponding assumed value of σt2. The assumed value of σt2 may be taken a little higher than the σt1 to start iterations. Now the elongation δp given by finite element analysis is compared against δ2 which is experimental value of elongation at load P2. If  2 p δ δ α − ≥  then σt2 is modified as follows. 2 δ ⎝⎠ ⎣⎦mWhere (σt2)m+1  = true stress at load P2 in (m+1)th iteration  (σt2)m  = true stress at load P2 in mth iteration   β  = Convergence control parameter ( 01 β < ≤ ) Iterations may be stopped when  2 p δ δ α − ≤ . At the final iteration (σt2, εt2) is the required second data point in the uniaxial true stress-true plastic strain curve.  e)  Similarly, the third data point in the true stress – true strain curve is obtained by considering the load P3, elastic modulus E, the previous points on the true stress-true strain curve i.e. (σt1, εt1), (σt2, εt2), the true strain (εt3) as obtained from the miniature test and the assumed value of stress σt3. Now the inverse FE analysis is carried out by iterating on σt3 till the complete match is obtained between the load-elongation curves of the miniature test and the inverse FE. At the final iteration the assumed stress value σt3  and the true strain  εt3 is the required third data point on the uniaxial true  stress-true strain curve. Likewise rest of the  data points on  the true stress –true strain curve are obtained by proceeding in the same manner.  f)  The material properties of the unknown material are determined in terms of Young’s modulus, yield stress  and data points on uniaxial true stress-true plastic strain curve. Once the  material properties are known, the direct finite element analysis can simulate miniature specimen test in much better way and can do in-depth analysis of miniature specimen test.  4. Results The inverse  finite element algorithm developed in  the present  study for the analysis of dumb-bell shaped miniature specimen under  in-plane tensile load was implemented with the help of the ABAQUS code. The miniature test load-elongation  curves in combination with the inverse finite element method may provide best estimates of conventionally measured tensile properties for different materials. Figure 3 shows that the load-elongation curves as obtained from the  inverse finite element procedure are matching completely against the one obtained from  the miniature test on the specimen from the AR66 alloy for a unique combination of constitutive parameters.  Table 2 shows the comparison of elastic modulus value obtained from the inverse finite element model and from the standard test. The starting value of Young’s modulus is taken as 70 GPa.  Table 2. Comparison of elastic modulus (E) from standard test and inverse FE for AR66 alloy  Method  (E) in GPa Uniaxial test  70.65 Inverse FEM  71.00  The developed procedure requires repeated finite element analysis as different data points on the true stress-true strain curve are obtained  by considering  the different  segments of miniature test load-elongation curve. The procedure employed here is the one that consists simply of matching the load–elongation curve obtained from the inverse finite element analysis to the experimental curve up to the segment under consideration. When a complete match is found between the load-elongation curves of the  miniature test  and the one from the inverse  finite element  method,  it gives the constitutive behaviour  of the unknown material. Figure 6 shows the comparison of true  stress–true strain curve obtained from the standard tensile test with that obtained by using inverse finite element procedure for the miniature specimen from used in the present investigation. It is observed from the figure that the results are encouraging and the predicted true stress-true strain diagram  corroborates well with the standard test curve. 4004505005506006507000 0.03 0.06 0.09 0.12True plastic strainTrue stress in MPaUniaxial testInverse FEM Fig. 6. Comparison of true stress–true plastic strain by inverse FE and uniaxial test for the AR66 alloy.  5. Conclusions  The determination of constitutive tensile behavior of any unknown material is made possible using the inverse finite element procedure as outlined above. The elastic modulus of  unknown material is determined with the help of the initial slope of the miniature specimen’s load-elongation  curve and repeated inverse finite element analysis. The results from the inverse finite element are comparing well with the standard test results. The approach  seems to have  potential to predict the  mechanical properties of the material in the in-service structures, which could be used in remaining life estimation.  The proposed dumb-bell shaped miniature specimen and the designed loading geometry in the present investigation  have some  special advantages in finite element modeling.
  1. 上一篇:3D下颌覆盖义齿英文文献和中文翻译
  2. 下一篇:夹具结构设计英文文献和中文翻译
  1. 压力阀迷宫通道流量特性英文文献和中文翻译

  2. 船舶结构优化设计英文文献和中文翻译

  3. 波士顿托宾纪念大桥的结...

  4. 抗侧向荷载的结构体系英文文献和参考文献

  5. 船体结构初步设计英文文献和中文翻译

  6. 连续大跨度桥梁结构英文文献和中文翻译

  7. 非线性循环行为混杂纤维...

  8. 中考体育项目与体育教学合理结合的研究

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 酸性水汽提装置总汽提塔设计+CAD图纸

  11. java+mysql车辆管理系统的设计+源代码

  12. 乳业同业并购式全产业链...

  13. 电站锅炉暖风器设计任务书

  14. 杂拟谷盗体内共生菌沃尔...

  15. 十二层带中心支撑钢结构...

  16. 大众媒体对公共政策制定的影响

  17. 当代大学生慈善意识研究+文献综述

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回