菜单
  

    Density

    The PFI refining increased the handsheet density by about 93%.Removing the fines (P200) resulted in a 12% drop in sheet density when compared to the refined pulp (R28+R48), implying that the contribution of fines to the sheet density was relatively small despite their remarkable influence on freeness. Further removal of R200 only slightly reduced the sheet density, suggesting the fibrous elements were stiff.

    Tensile index

    The PFI refining increased the tensile index by 144% (TABLE III), yielding a tensile index of 50 N*m/g, which is remarkable for a softwood TMP. It would be interesting to see where did the improvement come from. Progressive elimination of fines (P200) and short fibres (R200) reveals that a loss of 30% in tensile index of the refined pulp could be attributed to the fines and about 7% to the short fibres. Hence, one could assume that approximately 60% of the improvement by PFI refining was accounted for by the longer fibres, that is R28, R48 and R100 combined. This means that the bonding potential of the longer fibres could be ameliorated by the PFI refining. Noteworthily, the improvement in fibre bonding of the long fibres might be due to the fact that these fibres had already absorbed a lot of mechanical energy during the primary and secondary refining and, hence, they were more amendable when subjected to further mechanical treatment in a PFI mill.

    Tear index

    As noted in TABLE III, the PFI refining had a serious negative effect on fibre length by decreasing the tear index by about 16%. However, eliminating the P200 and R200 fractions marginally improved the tearing resistance, which is probably due to the increase in average fibre length. At the conclusion of the trials, the mill elected to remove the two 26-in. double disc refiners and use only the new conical refiner for production. This reduced the process refiners from two to one and reduced total connected energy by 450 hp, equating to energy savings of approximately $76,000/yr. In addition to energy reduction, the mill realized savings by reduction in maintenance and number of fillings purchased annually.

     In August 1999, one of the new triple-cone refiners was installed in an upper mid- western U.S. linerboard mill. At the time, the mill was operating one 34-in. double disc refiner with an 800-hp motor processing 150 to 180 tpd of OCC for the top sheet of its two-ply liner. The mill had determined that a second 34-in. double disc refiner operating in series with the existing refiner was required to achieve the new benchmarks that had been set for the final product. However, upon investigation of the new conical refiner and the results at the Brazilian beta site, the mill project team decided to test a conical refiner to see if it could provide the performance required. 

    The existing 34-in. double disc refiner was removed. The new triple-cone refiner was installed in its place and connected to the existing 800-hp motor. The total motor output was limited to 600-hp, keeping in line with the design criteria of the new refiner. At startup, the new refiner achieved the necessary paper tests on ts own but used only 375 gross horsepower. After a three-month trial, the refiner control was switched over to the mill DCS, and the gross refining power increased to 425 to 450 hp, depending on grade and tonnage. According to the mill, the new refiner is the most stable in DCS control and requires significantly less operator and maintenance attention compared with its double disc refiners. Overall energy savings from the installation is approximately $146,000/yr.

    In addition to reducing the energy required for refining, the mill also saved the expense associated with purchasing and maintaining two refiners and motors. An added benefit is tackle life, since the first set of tackle lasted 8 months compared with 60 days for the previous disc refiner. This mill is now evaluating installing two more of the triple-cone refiners in place of the three double disc refiners operating on the base sheet. It is expected that the overall sheet properties will improve when this takes place. The fillings in the refiners can then be optimized to provide fibrillation in the primary refiner for overall strength properties. The tickler refiner can be used for slight cutting to improve ring crush and ply bond. Overall energy savings are projected to be $438,900/yr.

  1. 上一篇:煤粉燃烧和NO形成的数值模拟英文文献和中文翻译
  2. 下一篇:机械设计英文文献及中文翻译
  1. 层残余应力钢钛刀具磨损英文文献和中文翻译

  2. 数控车床上磨削主轴的分析

  3. 圆锥破碎机磨损模型英文文献和中文翻译

  4. 疏磨机设计英文文献和中文翻译

  5. 振动磨机英文文献和中文翻译

  6. 数控系统在平面磨床上应...

  7. 鄂式破碎机耐磨衬板英文文献和中文翻译

  8. 乳业同业并购式全产业链...

  9. 十二层带中心支撑钢结构...

  10. 大众媒体对公共政策制定的影响

  11. 电站锅炉暖风器设计任务书

  12. 当代大学生慈善意识研究+文献综述

  13. 酸性水汽提装置总汽提塔设计+CAD图纸

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. 中考体育项目与体育教学合理结合的研究

  16. 杂拟谷盗体内共生菌沃尔...

  17. java+mysql车辆管理系统的设计+源代码

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回