菜单
  

    genieur und Architekten Vereins, and in 1896 by Mandl with
    publications in the journal Zeitschrift des O ¨ sterreichischen In-
    genieur und Architekten Vereins. Melan’s method is shown in
    Eqs. (22)–(24) of Gori (1999).
    At the end of 19th century, in Belgium, Paul Christophe
    published a method for calculating the stresses due to bending
    in the Annales des Travaux publics de Belgique (Christophe
    1899). This method was like that considered by Max Ritter
    von Thullie for the concrete in RC members, in its second
    phase (von Thullie 1896, 1897). Christophe’s proposed cal-
    culation method was soon in widespread use. Von Thullie
    methods, which consider also a nonlinear behavior of com-
    pressed concrete, are described in detail in Eqs. (28)–(39) of
    Gori (1999).
    In France, Edmond Coignet and N. De Tedesco published
    a method ‘‘du calcul des ouvrages en ciment arme ´ avec os-
    sature metallique’’ in the Bullettin de la Socie ´te ´ des Inge ´nieurs
    Civils de France (Coignet and de Tedesco 1894), summarized
    in Eqs. (25)–(27) of Gori (1999), which became very popular
    for its simplicity.
    Again, Stellet published a work in Reveu Tecnique, and L.
    Lefort in 1898 published his theories in Nouvelles Annales de
    la Construction, Eqs. (40)–(43) of Gori (1999).
    While Conside `re was at work in France, in SwitzerlandWil-
    helm Ritter, professor of the Zurich Polytechnic, published his
    theories in the Schweizerische Bauzeitung in 1899, considering
    a nonlinear behavior of concrete (Ritter 1899). He proposed a
    calculation method that quickly became the commonly used
    in Switzerland, described in Eqs. (44)–(54) of Gori (1999).
    In the same years, Franc ¸ois Hennebique developed his own
    particular design method and recommended all the holders of
    his patent rights in Europe to adopt it. This method was not
    J. Perform. Constr. Facil. 1999.13:67-75.
    Downloaded from ascelibrary.org by SHANGHAI INSTITUTE OF on 12/12/12. Copyright ASCE. For personal use only; all rights reserved.JOURNAL OF PERFORMANCE OF CONSTRUCTED FACILITIES / MAY 1999 / 69
    FIG. 4. Analyses of Simple RC Rectangular Section Beam (b =40cm; h = 100 cm; AS = 10–30 cm2
    ) Subjected to Bending (M = 400
    kN?m), Following Various Theories: Position of Neutral AxisWhen Varying Cross-Sectional Area of Metal Reinforcement
    FIG. 3. Analyses of Simple RC Rectangular Section Beam (b =40cm; h = 60–140 cm; AS =20cm2
    ) Subjected to Bending (M = 400
    kN?m), Following Various Theories: Maximum Tensile Stress of Metal ReinforcementWhen Varying Depth of Section
    the outcome of any particular theory; it was the outcome of a
    practical calculation procedure, in which the safety coefficients
    were adapted on the basis of experience (de Tedesco and Mau-
    rel 1904).
    COMPARISON OF VARIOUS ANALYSIS METHODS
    FOR BENDING
    In the following is given a comparison between the first
    methods for verifying simple bending in rectangular sections
    with a single metal reinforcement position, described by Gori
    (1999), to analyze the quantitative influence of the various
    calculation methods on practical problems.
    Firstly, a particular rectangular section concrete beam, singly
    reinforced, subjected to simple bending, has been analyzed.
    The diagrams of Figs. 1–6 show the values of the neutral
    axis position (Figs. 1 and 4), of the maximum stresses of con-
    crete (Figs. 2 and 5), and of metal (Figs. 3 and 6) in relation
    to that rectangular RC section in which just one geometrical
    parameter has been varied (within allowable limits) while
    maintaining the other parameters constant (Gori and Simon-
    celli 1994).
    In all the diagrams the following parameters are assumed
  1. 上一篇:精益生产再设计流水线英文文献和翻译
  2. 下一篇:资产重组问题与应对策略开题报告
  1. 船体梁极限强度英文文献和中文翻译

  2. 加固纤维聚合物增强混凝...

  3. 连续大跨度桥梁结构英文文献和中文翻译

  4. 钢筋混凝土柱在火灾中的...

  5. H横梁和水泥土挡土墙相互...

  6. 振动台实验和动态响应地...

  7. 钢筋混凝土框架英文文献和中文翻译

  8. 当代大学生慈善意识研究+文献综述

  9. 酸性水汽提装置总汽提塔设计+CAD图纸

  10. 乳业同业并购式全产业链...

  11. 电站锅炉暖风器设计任务书

  12. java+mysql车辆管理系统的设计+源代码

  13. 大众媒体对公共政策制定的影响

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. 十二层带中心支撑钢结构...

  16. 中考体育项目与体育教学合理结合的研究

  17. 杂拟谷盗体内共生菌沃尔...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回